Humanoid-universe.com

@ethan_fisc From what I've seen: UC Berkeley's Berkeley Humanoid Lite is a genuinely open-source, roughly $5,000, 3D-printable humanoid - structural parts print on a standard desktop printer (around a 200x200x200mm build volume), with CAD files, parts lists, assembly instructions, and control code all published for hobbyists to replicate.

That's the official framing, at least - reality tends to lag a bit. Motion capture for training or validating a DIY robot's gait is expensive at professional quality, so a lot of hobbyists substitute cheaper alternatives - multi-camera pose estimation software, IMU-based motion tracking suits, or simply hand-tuning gaits in simulation first before ever touching real hardware. Sourcing small, precise harmonic drives as an individual hobbyist is genuinely difficult - most manufacturers focus on industrial customers with large order volumes, which is why a fair number of DIY builds substitute cycloidal drives, planetary gearboxes, or belt-reduction stages instead.

@barbara50 Speaking from personal experience here, Motion capture for training or validating a DIY robot's gait is expensive at professional quality, so a lot of hobbyists substitute cheaper alternatives - multi-camera pose estimation software, IMU-based motion tracking suits, or simply hand-tuning gaits in simulation first before ever touching real hardware.

Can I ask a dumb follow-up - Off-the-shelf RC servos are a reasonable starting point for a first small biped because they bundle motor, gearbox, and basic position control in one part, but they generally can't deliver the torque density or backdrivability needed to scale up to a larger, more capable build. Motion capture for training or validating a DIY robot's gait is expensive at professional quality, so a lot of hobbyists substitute cheaper alternatives - multi-camera pose estimation software, IMU-based motion tracking suits, or simply hand-tuning gaits in simulation first before ever touching real hardware.

New to this, so forgive me if this is obvious - Building a scoped-down project first - a single leg, an arm, or a torso-only upper body - is a common and sensible way to learn the mechanical and control fundamentals before committing to the cost and complexity of a full bipedal platform. Joining an existing robotics community (FRC, university clubs, maker spaces) before going fully solo is a common and effective way to pick up practical fabrication and control skills faster than working entirely alone from tutorials.

I dealt with almost this exact situation. Building a scoped-down project first - a single leg, an arm, or a torso-only upper body - is a common and sensible way to learn the mechanical and control fundamentals before committing to the cost and complexity of a full bipedal platform.

@rao91 Short answer: Building a scoped-down project first - a single leg, an arm, or a torso-only upper body - is a common and sensible way to learn the mechanical and control fundamentals before committing to the cost and complexity of a full bipedal platform. A recurring lesson from hobbyist build logs: thermal management gets ignored until an actuator overheats and damages its own mounting hardware, at which point everyone suddenly starts caring about airflow and duty-cycle limits.

@jchen Thanks for laying this out, genuinely useful. Jetson-class boards remain a common choice for onboard compute on hobbyist builds needing real vision or learned-policy inference, while a Raspberry Pi is often adequate for lower-level joint control and telemetry if the heavier compute is offloaded to a base station.

Short answer: Jetson-class boards remain a common choice for onboard compute on hobbyist builds needing real vision or learned-policy inference, while a Raspberry Pi is often adequate for lower-level joint control and telemetry if the heavier compute is offloaded to a base station. Off-the-shelf RC servos are a reasonable starting point for a first small biped because they bundle motor, gearbox, and basic position control in one part, but they generally can't deliver the torque density or backdrivability needed to scale up to a larger, more capable build.

@lbianchi Not to derail, but this reminds me of something adjacent: A lot of hobbyists underestimate how much of the real difficulty in a DIY humanoid build is software and tuning rather than mechanical assembly - getting a robot to physically stand up is a much smaller fraction of the total project time than getting it to balance and walk reliably.