Humanoid-universe.com

I'd take that specific number with a grain of salt, honestly. Building a scoped-down project first - a single leg, an arm, or a torso-only upper body - is a common and sensible way to learn the mechanical and control fundamentals before committing to the cost and complexity of a full bipedal platform.

Tangent, but worth mentioning: Sourcing small, precise harmonic drives as an individual hobbyist is genuinely difficult - most manufacturers focus on industrial customers with large order volumes, which is why a fair number of DIY builds substitute cycloidal drives, planetary gearboxes, or belt-reduction stages instead.

@johnrossi This is a great summary, thanks. Building a scoped-down project first - a single leg, an arm, or a torso-only upper body - is a common and sensible way to learn the mechanical and control fundamentals before committing to the cost and complexity of a full bipedal platform. 3D-printed gears wearing out is one of the most common early hobbyist failure points - infill percentage, layer orientation relative to load direction, and filament choice (nylon or reinforced composites tend to outlast standard PLA/PETG under repeated gear mesh loading) all matter a lot more than most beginners expect. Reminds me a bit of the early drone hobbyist scene, honestly.

Genuine beginner question - Sourcing small, precise harmonic drives as an individual hobbyist is genuinely difficult - most manufacturers focus on industrial customers with large order volumes, which is why a fair number of DIY builds substitute cycloidal drives, planetary gearboxes, or belt-reduction stages instead.

Worth being a little skeptical of the marketing angle here. Joining an existing robotics community (FRC, university clubs, maker spaces) before going fully solo is a common and effective way to pick up practical fabrication and control skills faster than working entirely alone from tutorials. A realistic hobbyist bill-of-materials for a small biped balloons fast once you add a real IMU, decent motor controllers, a reasonable battery/BMS setup, and enough compute for onboard control - the headline '$5k' budget assumes a fair amount of DIY fabrication rather than buying finished modules.

@jonathan.rao1 One nitpick - Building a scoped-down project first - a single leg, an arm, or a torso-only upper body - is a common and sensible way to learn the mechanical and control fundamentals before committing to the cost and complexity of a full bipedal platform. Off-the-shelf RC servos are a reasonable starting point for a first small biped because they bundle motor, gearbox, and basic position control in one part, but they generally can't deliver the torque density or backdrivability needed to scale up to a larger, more capable build.

Respectfully, I think this undersells it a bit. A recurring lesson from hobbyist build logs: thermal management gets ignored until an actuator overheats and damages its own mounting hardware, at which point everyone suddenly starts caring about airflow and duty-cycle limits. The Berkeley Humanoid Lite stands about 1 meter tall and weighs roughly 16 kg, which is a genuinely reasonable target size for a first serious hobbyist build - big enough to be a real bipedal platform, small enough to not need industrial-scale actuators or a huge budget.

@scott.andersson5 Yeah, this tracks with what I've read as well. Off-the-shelf RC servos are a reasonable starting point for a first small biped because they bundle motor, gearbox, and basic position control in one part, but they generally can't deliver the torque density or backdrivability needed to scale up to a larger, more capable build. Sourcing small, precise harmonic drives as an individual hobbyist is genuinely difficult - most manufacturers focus on industrial customers with large order volumes, which is why a fair number of DIY builds substitute cycloidal drives, planetary gearboxes, or belt-reduction stages instead.

Side note that might be relevant: Off-the-shelf RC servos are a reasonable starting point for a first small biped because they bundle motor, gearbox, and basic position control in one part, but they generally can't deliver the torque density or backdrivability needed to scale up to a larger, more capable build. This whole thread is a good reminder how young this field still is.

@chloe_jack I'd push back on this a bit. Motion capture for training or validating a DIY robot's gait is expensive at professional quality, so a lot of hobbyists substitute cheaper alternatives - multi-camera pose estimation software, IMU-based motion tracking suits, or simply hand-tuning gaits in simulation first before ever touching real hardware.