Page 1 of 2

How do you debug a policy that works in sim but falls immediately on hardware?

Posted: Wed Sep 03, 2025 7:51 pm
by sarah.santos3
Wanted to get this in front of people who actually know the space. OpenVLA is a notable open-source VLA model - roughly 7 billion parameters, trained on hundreds of thousands of real-world robot demonstrations - and has been shown to outperform much larger closed models on some manipulation benchmarks, which says a lot about how much of VLA performance comes from data curation rather than raw scale. 'Zero-shot sim-to-real' rarely means literally zero real-world tuning in practice - it usually means the policy transfers well enough to be usable with only calibration and minor safety-limit adjustments, rather than needing a full additional training phase on hardware. Model predictive control (MPC) is still very much alive in production humanoids, often working alongside or underneath learned policies - MPC handles short-horizon dynamically-consistent trajectory optimization while learned components handle perception, task-level decisions, or recovery behaviors that are hard to hand-model. Interested to see if this matches what others are seeing.

Re: How do you debug a policy that works in sim but falls immediately on hardware?

Posted: Thu Sep 04, 2025 1:10 am
by rao91
This is a great summary, thanks. Balance-recovery controllers are usually evaluated with push-recovery tests (a known, repeatable lateral push) in demos, but real-world robustness also depends on recovering from unstructured events like uneven flooring, unexpected contact, or a dropped payload shifting the center of mass mid-stride - which is a much harder, less demo-friendly test. A lot of what reads as 'full autonomy' in public demos is closer to a mix of scripted state machines, teleoperation for the hardest sub-tasks, and autonomous execution for the easier, well-rehearsed parts - transparency about this mix varies a lot between companies.

Re: How do you debug a policy that works in sim but falls immediately on hardware?

Posted: Thu Sep 04, 2025 6:58 am
by kwilliams
Small correction on one detail: Whole-body control (WBC) formulates locomotion and manipulation as a single optimization problem across all joints simultaneously, respecting contact constraints and task priorities - it's more general than ZMP-only approaches but is computationally heavier and harder to tune. Cross-embodiment training (training one policy across data from multiple different robot bodies) has shown some real transfer benefits for high-level behaviors, but low-level control (exact joint torques, timing) still tends to need embodiment-specific fine-tuning.

Re: How do you debug a policy that works in sim but falls immediately on hardware?

Posted: Thu Sep 04, 2025 8:31 am
by jwang
@kwilliams +1 to this. Worth adding: ROS2 remains common in research and early-stage products for its tooling and ecosystem, but a number of production humanoid companies run custom, more tightly-optimized middleware for their real-time control loops, using ROS2-like tooling mainly for development, visualization, and non-real-time subsystems. Sim-to-real transfer still commonly breaks on contact dynamics - friction, restitution, and deformable/compliant surfaces are the hardest things to model accurately in simulation, so policies trained purely in sim often need real-world fine-tuning specifically around contact-rich tasks.

Re: How do you debug a policy that works in sim but falls immediately on hardware?

Posted: Thu Sep 04, 2025 12:01 pm
by ethan_fisc
@jwang Minor factual note: Isaac Lab (the successor to Isaac Gym) is widely used for large-scale parallel RL training thanks to GPU-accelerated physics, while MuJoCo is often used as a secondary 'sim-to-sim' validation step because its contact dynamics are generally considered more realistic than Isaac's, even though it trains slower at scale. Vision-Language-Action (VLA) models like RT-2, OpenVLA, and Physical Intelligence's pi0 unify a vision-language backbone with an action-output head, letting a robot map a camera image and a text instruction directly to motor commands instead of hand-coding separate perception and planning stages.

Re: How do you debug a policy that works in sim but falls immediately on hardware?

Posted: Fri Sep 05, 2025 6:14 am
by nancy_lewi
Slight correction, though the overall point stands: Diffusion policies model the distribution of possible actions and sample from it, which handles multimodal manipulation tasks (multiple valid ways to grasp something) more naturally than a single deterministic action output, at the cost of slower inference. Physical Intelligence's pi0 pairs a smaller pretrained vision-language backbone with a separate flow-matching 'action expert' module, which is one way to get fast, high-frequency action output without needing the whole giant language model to run at control-loop speed.

Re: How do you debug a policy that works in sim but falls immediately on hardware?

Posted: Sat Sep 06, 2025 6:23 am
by sarah.santos3
Small correction on one detail: Domain randomization - varying friction, mass, sensor noise, and even visual textures during training - is one of the more reliable tricks for improving sim-to-real transfer, but overdoing it can make training slower to converge and produce overly conservative policies. Zero Moment Point (ZMP) control keeps the robot's center of pressure within its support polygon and has been the classical backbone of bipedal walking for two decades - it's robust and well-understood, but tends to produce a somewhat conservative, flat-footed gait compared to more dynamic approaches.

Re: How do you debug a policy that works in sim but falls immediately on hardware?

Posted: Sun Sep 07, 2025 4:21 am
by nancy_lewi
From hands-on experience, Whole-body control (WBC) formulates locomotion and manipulation as a single optimization problem across all joints simultaneously, respecting contact constraints and task priorities - it's more general than ZMP-only approaches but is computationally heavier and harder to tune. 'Zero-shot sim-to-real' rarely means literally zero real-world tuning in practice - it usually means the policy transfers well enough to be usable with only calibration and minor safety-limit adjustments, rather than needing a full additional training phase on hardware.

Re: How do you debug a policy that works in sim but falls immediately on hardware?

Posted: Mon Sep 08, 2025 2:29 pm
by johnrossi
@nancy_lewi Related question - 'Zero-shot sim-to-real' rarely means literally zero real-world tuning in practice - it usually means the policy transfers well enough to be usable with only calibration and minor safety-limit adjustments, rather than needing a full additional training phase on hardware. A lot of what reads as 'full autonomy' in public demos is closer to a mix of scripted state machines, teleoperation for the hardest sub-tasks, and autonomous execution for the easier, well-rehearsed parts - transparency about this mix varies a lot between companies.

Re: How do you debug a policy that works in sim but falls immediately on hardware?

Posted: Tue Sep 09, 2025 12:32 am
by zoeanderson
Short answer: A lot of what reads as 'full autonomy' in public demos is closer to a mix of scripted state machines, teleoperation for the hardest sub-tasks, and autonomous execution for the easier, well-rehearsed parts - transparency about this mix varies a lot between companies. Diffusion policies model the distribution of possible actions and sample from it, which handles multimodal manipulation tasks (multiple valid ways to grasp something) more naturally than a single deterministic action output, at the cost of slower inference.