How do you validate depth camera accuracy at typical grasp distances?

[sharonschmidt]

This is a great summary, thanks. LiDAR gives reliable, lighting-independent range data but is heavier, pricier, and gives sparser point clouds up close than stereo or depth cameras, which is why a lot of humanoids lean on stereo/depth cameras for near-field manipulation and reserve LiDAR (if present at all) for longer-range navigation.

[sandra_ivan]

I can speak to this a bit. IMU drift over time (bias instability) is usually the real culprit behind slowly diverging state estimates, not noise - it's typically handled with sensor fusion against other references (visual odometry, joint kinematics) rather than trying to eliminate drift at the source. SLAM in a working warehouse is harder than in a controlled lab mainly because the map keeps changing - pallets move, people walk through, lighting shifts near dock doors - so a lot of production systems lean on semi-static maps refreshed periodically rather than pure continuous SLAM. Totally unrelated but has anyone else noticed how fast component costs are dropping this year.

[forgecam45]

This lines up with my experience. Force/torque sensors near the ankle give a direct read on ground reaction forces, which is valuable for balance control, but they add cost, a failure point, and routing complexity right at a joint that already takes the most mechanical abuse.

[sven.wilson4]

Respectfully, I think this undersells it a bit. Estimating joint torque from motor current draw is cheap and requires no extra sensor, but it's less accurate than a dedicated torque sensor because it doesn't capture friction losses through the gearbox - good enough for coarse control, not always for precise force-controlled tasks. Vibration is one of the most underrated sources of noisy IMU and tactile readings - mounting matters as much as sensor quality, and a poorly isolated mount can add more noise than the sensor's own datasheet specs would suggest.

[nicole57]

@sven.wilson4 Genuinely curious - Multi-camera calibration drifts over time from thermal expansion, vibration, and mechanical wear, which is why production systems typically run periodic recalibration routines rather than assuming a one-time factory calibration holds forever. Sensor fusion mostly earns its keep by covering for each individual sensor's weaknesses - vision struggles with occlusion and lighting, IMUs drift, force/torque sensors are noisy at low loads - fusing them gives a more robust estimate than any one source alone, independent of raw compute.

[garcia51]

@nicole57 Slight correction, though the overall point stands: Event cameras (which report per-pixel brightness changes rather than full frames) are still more of a research curiosity than a production sensor for humanoids, mainly because the software ecosystem and processing pipelines around them are far less mature than for standard frame-based cameras. SLAM in a working warehouse is harder than in a controlled lab mainly because the map keeps changing - pallets move, people walk through, lighting shifts near dock doors - so a lot of production systems lean on semi-static maps refreshed periodically rather than pure continuous SLAM.

[emily.kumar]

Speaking from personal experience here, Tactile skin arrays have improved a lot, but 'good enough to matter' really depends on the task - coarse contact detection across a large area is fairly mature, while fine, high-resolution force distribution sensing (like a human fingertip) is still the harder problem. IMU drift over time (bias instability) is usually the real culprit behind slowly diverging state estimates, not noise - it's typically handled with sensor fusion against other references (visual odometry, joint kinematics) rather than trying to eliminate drift at the source.

[barbara50]

@emily.kumar Just to be precise about one thing: Tactile skin arrays have improved a lot, but 'good enough to matter' really depends on the task - coarse contact detection across a large area is fairly mature, while fine, high-resolution force distribution sensing (like a human fingertip) is still the harder problem. A minimum viable sensing suite for safe bipedal walking generally includes joint encoders, an IMU for orientation/angular velocity, and either force/torque sensing or accurate current-based torque estimation at the ankles - everything else (vision, tactile, LiDAR) adds capability rather than being strictly required just to stay upright.

[shill]

@barbara50 That's the official framing, at least - reality tends to lag a bit. Proprioception (the robot's sense of its own joint angles, velocities, and forces) tends to get less attention than flashy vision systems, even though a lot of balance and manipulation failures trace back to proprioceptive noise or miscalibration rather than a vision problem. Multi-camera calibration drifts over time from thermal expansion, vibration, and mechanical wear, which is why production systems typically run periodic recalibration routines rather than assuming a one-time factory calibration holds forever.

[karen_kim]

@shill Slight correction, though the overall point stands: SLAM in a working warehouse is harder than in a controlled lab mainly because the map keeps changing - pallets move, people walk through, lighting shifts near dock doors - so a lot of production systems lean on semi-static maps refreshed periodically rather than pure continuous SLAM.