Sharing video of my robot's first 10 steps (fell on step 11, still counts)

[servoken70]

@mia_lars Ran into exactly this myself. 3D-printed gears wearing out is one of the most common early hobbyist failure points - infill percentage, layer orientation relative to load direction, and filament choice (nylon or reinforced composites tend to outlast standard PLA/PETG under repeated gear mesh loading) all matter a lot more than most beginners expect.

[benjaminsanchez]

@servoken70 Same conclusion I've come to. Also worth noting: 3D-printed gears wearing out is one of the most common early hobbyist failure points - infill percentage, layer orientation relative to load direction, and filament choice (nylon or reinforced composites tend to outlast standard PLA/PETG under repeated gear mesh loading) all matter a lot more than most beginners expect.

[carlossanchez]

This matches something I went through recently. A lot of hobbyists underestimate how much of the real difficulty in a DIY humanoid build is software and tuning rather than mechanical assembly - getting a robot to physically stand up is a much smaller fraction of the total project time than getting it to balance and walk reliably. Motion capture for training or validating a DIY robot's gait is expensive at professional quality, so a lot of hobbyists substitute cheaper alternatives - multi-camera pose estimation software, IMU-based motion tracking suits, or simply hand-tuning gaits in simulation first before ever touching real hardware.

[deborahperez]

New to this, so forgive me if this is obvious - The Berkeley Humanoid Lite stands about 1 meter tall and weighs roughly 16 kg, which is a genuinely reasonable target size for a first serious hobbyist build - big enough to be a real bipedal platform, small enough to not need industrial-scale actuators or a huge budget.

[scott.andersson5]

This is exactly the kind of context I was looking for. A first successful unassisted walk, from a standing start on a from-scratch project, commonly takes many months of part-time weekend work even for someone with a solid mechanical and software background - it's a genuinely hard milestone, not a weekend project. Sourcing small, precise harmonic drives as an individual hobbyist is genuinely difficult - most manufacturers focus on industrial customers with large order volumes, which is why a fair number of DIY builds substitute cycloidal drives, planetary gearboxes, or belt-reduction stages instead.

[ethan_fisc]

Genuine beginner question - The Berkeley Humanoid Lite stands about 1 meter tall and weighs roughly 16 kg, which is a genuinely reasonable target size for a first serious hobbyist build - big enough to be a real bipedal platform, small enough to not need industrial-scale actuators or a huge budget. Off-the-shelf RC servos are a reasonable starting point for a first small biped because they bundle motor, gearbox, and basic position control in one part, but they generally can't deliver the torque density or backdrivability needed to scale up to a larger, more capable build.

[chenperez]

@ethan_fisc This lines up with my experience. The Berkeley Humanoid Lite stands about 1 meter tall and weighs roughly 16 kg, which is a genuinely reasonable target size for a first serious hobbyist build - big enough to be a real bipedal platform, small enough to not need industrial-scale actuators or a huge budget. Group-buy arrangements for harder-to-source parts (small harmonic drives, precision bearings, custom PCBs) are a common way hobbyist communities work around the fact that specialty components are often only sold in industrial minimum-order quantities.

[jonathan.rao1]

@chenperez Slightly off-topic, but related: A first successful unassisted walk, from a standing start on a from-scratch project, commonly takes many months of part-time weekend work even for someone with a solid mechanical and software background - it's a genuinely hard milestone, not a weekend project. Building a scoped-down project first - a single leg, an arm, or a torso-only upper body - is a common and sensible way to learn the mechanical and control fundamentals before committing to the cost and complexity of a full bipedal platform. Totally unrelated but has anyone else noticed how fast component costs are dropping this year.

[scott21]

@jonathan.rao1 Can I ask a dumb follow-up - Joining an existing robotics community (FRC, university clubs, maker spaces) before going fully solo is a common and effective way to pick up practical fabrication and control skills faster than working entirely alone from tutorials.

[erik_novi]

This matches something I went through recently. The Berkeley Humanoid Lite stands about 1 meter tall and weighs roughly 16 kg, which is a genuinely reasonable target size for a first serious hobbyist build - big enough to be a real bipedal platform, small enough to not need industrial-scale actuators or a huge budget.