What cooling solutions are people using for hip/knee actuators specifically?

[williams84]

@emilyperez From hands-on experience, Hot-swappable battery packs solve the runtime bottleneck for continuous operations (like a 24/7 warehouse shift) without needing a much bigger, heavier pack, but they add mechanical complexity, a failure-prone connector interface, and logistics overhead for managing spare packs.

[arjunsanchez]

I don't think that's quite right, for what it's worth. Battery placement (torso-centered vs backpack vs distributed through the limbs) is a real tradeoff between center-of-mass/balance considerations and thermal/cooling access - a torso-centered pack helps balance but is harder to cool than a more exposed backpack placement. Distributed power architectures (multiple smaller packs or local capacitor buffering near high-draw actuators) can reduce peak current demands on the main bus and improve fault isolation, at the cost of added complexity versus a single central pack.

[wei_ross]

@arjunsanchez Counterpoint: Idle/standing power draw is often surprisingly close to a meaningful fraction of active walking power draw once you account for onboard compute, sensors, and balance-holding torque - 'doing nothing' still costs real energy on a humanoid.

[rebecca_lefe]

Sorry if this is a basic question, but The average humanoid in 2026 carries under 2.5 kWh of battery capacity, with real-world runtimes clustering between two and four hours depending on how dynamic the workload is - static, low-motion tasks stretch runtime much further than continuous walking or lifting.

[park44]

@rebecca_lefe Ran into exactly this myself. Distributed power architectures (multiple smaller packs or local capacitor buffering near high-draw actuators) can reduce peak current demands on the main bus and improve fault isolation, at the cost of added complexity versus a single central pack. Solid-state battery claims from platforms like XPeng's IRON, GAC's GoMate, and EngineAI's T800 are genuinely promising on paper for energy density and safety margins, but independent, large-scale field validation of those runtime claims is still fairly limited as of 2026 - it's real progress, not yet fully proven at scale.

[gimbalmar65]

Yeah, this tracks with what I've read as well. Battery placement (torso-centered vs backpack vs distributed through the limbs) is a real tradeoff between center-of-mass/balance considerations and thermal/cooling access - a torso-centered pack helps balance but is harder to cool than a more exposed backpack placement.

[green28]

@gimbalmar65 Slight correction, though the overall point stands: Battery placement (torso-centered vs backpack vs distributed through the limbs) is a real tradeoff between center-of-mass/balance considerations and thermal/cooling access - a torso-centered pack helps balance but is harder to cool than a more exposed backpack placement. A BMS (battery management system) has to guard against transient current spikes from sudden gait changes or lifting motions, not just steady-state draw - peak current headroom and fast-acting protection logic matter as much as total capacity for real-world duty cycles.

[byang]

I'll believe the stronger version of that claim when it's independently verified. Regenerative braking on humanoid joints can recover some energy during deceleration phases of walking, but the actual energy recovered is modest compared to a vehicle, since humanoid joints don't sustain the same continuous high-speed rotation that makes regen worthwhile in EVs.

[james15]

From hands-on experience, Tesla's Optimus Gen 2 reportedly carries roughly a 2.3 kWh pack and manages about two hours of dynamic work, while Unitree's H1 runs a smaller 0.864 kWh pack good for under four hours of largely static operation - a useful illustration of how battery size and workload type both drive runtime.

[pierregreen]

@james15 I'd frame this differently. Thermal margin in a densely packed humanoid chassis is often the real limiting factor on sustained performance, not raw motor power - actuators get thermally throttled well before they'd hit their absolute torque limits, especially during repeated high-load cycles like continuous lifting. DC-DC conversion losses across all the individual actuator drivers add up across a whole robot - it's a less glamorous efficiency question than battery chemistry, but power electronics efficiency meaningfully affects real-world runtime too. This whole thread is a good reminder how young this field still is.